Choose Quilling Strip Widths That Work in an Art Journal

Choose Quilling Strip Widths That Work in an Art Journal

Why strip width changes everything in a quilled journal

Quilling in an art journal is a different proposition from quilling on a card or a framed panel. The page turns, the book closes, and the coils sit beside writing, collage and painted grounds. The single decision that shapes the result most is strip width, because width governs how the paper behaves as you coil it, how the finished motif sits on the page, and how much room the closed journal needs.

Taking quilling into a journal is a natural next step for anyone who already enjoys rolling coils and shaping teardrops and marquises. The hobby becomes more personal when the motifs are part of a page: a border around a written memory, a loose spray above a photo, a few tight coils echoed in a painted pattern. Strip width is the lever that lets you move from a card that is looked at flat to a page that is handled, stacked and stored.

What width actually controls

A quilling strip is cut to a specific width, usually measured in millimetres, and that measurement describes the depth of the paper edge that faces you when the strip lies flat. It is not the same as the strip's length, which sets how large a coil can open, nor the same as paper weight, which affects stiffness and how well a coil holds its shape.

Narrow strips bend easily and coil into tight, fine circles. They suit delicate line work, small lettering, fine tendrils and dense fills where many small shapes sit close together. Wider strips carry more paper per coil, produce a chunkier edge, and hold broad, open shapes with a stronger presence. Because a wider strip shows more of its cut edge, the colour appears as a thick band rather than a thin line, and the motif reads as more solid from a distance.

Width, stiffness and grain

Width alone does not tell you how a strip will fold or hold. A wide strip cut from thin paper can flop; a narrow strip cut from stiff paper can fight the coil and crack when shaped. Quilling paper is normally cut with the grain running along the length so the strip coils smoothly, and pre-cut packs are sold on that basis. If you cut your own strips from a larger sheet, check the grain direction first by flexing the sheet gently: it curls more readily along one axis, and the strips should run that way. Paper weight in gsm is a rough guide to heft but not a measure of thickness, so judge a new paper by handling a test strip rather than by the number alone.

Matching width to the journal page

An art journal page is not a blank card. It already carries a ground, perhaps paint, gesso, collage or writing, and it may sit against a facing page. That changes the practical choice.

  • Fine work on a busy ground: narrow strips in the region of 3 mm read as crisp detail without competing with the background.
  • Bold motifs on a quieter page: widths around 5 to 7 mm give a coil real weight and let a few shapes carry the composition.
  • Borders and frames: a slightly wider strip creates a solid edge that frames a written area or a photograph.
  • Mixed pages: combining a fine outline with a few broader coils creates contrast without needing many shapes.

These are starting points, not rules. The useful test is to quill one small motif at the width you plan to use, place it on the page without gluing, and look at it from reading distance. If the shape disappears, go wider. If it overwhelms the page, go narrower.

Plan for the closed journal

Quilling sits proud of the page, so a wide coil built up in layers makes a thicker bump than a fine one. On a single loose sheet this hardly matters. In a journal that will be closed, stacked and carried, height accumulates. Keep the thickest motifs away from the spine and the page edges, group taller shapes in the middle of a page, and leave the facing page flatter where the two will meet. A journal with a little breathing room between pages, or one that is stored flat rather than crammed upright, handles quilled pages more comfortably than a tightly filled book.

Taking the hobby further with a wider palette of widths

Most quillers start with one width because a single pack is simple to buy and use. The next step is to think of width as a design variable alongside colour and shape. A small set of widths, perhaps one fine, one medium and one broad, lets you build motifs with internal contrast: a tight centre in a narrow strip, an outer ring in a wider one, a run of fine tendrils linking heavier shapes.

Pre-cut strips in a range of widths save the cutting and keep the edges even, which matters when several strips must sit side by side. A strip cutter or a slotted quilling board helps if you cut your own, and a fine-tipped slotted tool or a needle tool suits narrow strips while a slightly larger tool gives more control on broad coils. A cork or foam working surface lets you pin and shape motifs before gluing, and a fine applicator bottle for glue gives the small, controlled dots that quilled work needs.

Adhesive and paper choice

Quilling glue needs to hold a coil's end and join shapes without soaking the paper. A thin craft adhesive applied sparingly with a needle tip or fine applicator is easier to control than a thick squeeze of glue, and it dries without adding bulk. Test any adhesive on an offcut of the same paper before using it on the page, because how a paper accepts glue varies with its surface and weight. If the journal is a long-term keepsake, choose quilling paper and a page ground whose permanence suits the purpose; only papers described as acid-free by their maker carry that claim, so read the packaging rather than assuming it.

Building a journal page in a coherent order

Quilling is best added late, after the ground and any writing or collage are dry and settled. Work out the placement first, then glue the largest or heaviest motifs before the fine details so you have room to handle the page. Let each cluster set before adding the next, and keep the finished spread open and flat while it dries so coils do not slump. Finish by checking that no tall coil will press into the facing page when the journal closes.

The step from card-making to journal work is mostly a step in judgement: choosing a width that suits the page, handling the added depth, and letting fine and broad strips do different jobs. Once width becomes a deliberate choice, quilling stops being a single technique and becomes a way of drawing and layering on the page.

Back to blog

Useful Supplies for This Topic

Build paper layers and decorative details in your next creative journal.

Supplies, practical uses and Amazon links
SupplyWhat it helps withView
Botanical collage papers and stickersBuild botanical paper layers in a journal or collage.Amazon
Scrapbook adhesive tape runnersAttach suitable paper layers neatly in a card or scrapbook.Amazon
A5 paper trimmerTrim paper pieces that fit the cutter's working size.Amazon
Ink blending toolsBlend separately selected inks across paper-craft details.Amazon
Small-parts organizer boxesSeparate beads, findings and other small craft components.Amazon

As an Amazon Associate I earn from qualifying purchases.

Explore Our Digital Guides

Follow a clear plan for organizing, making and finishing your next project with our practical digital guides.