Choosing Book Board for Accordion Books and Turning Curiosity into a First Project
Share
An accordion book is a simple structure with a demanding component: the cover boards. The folded paper block is what makes the book open and flex; the boards are what protect the folds, hold the covers flat and give the whole object its weight and presence. Choosing a sensible board is also one of the easiest ways to turn a vague interest in bookbinding into a first project you can actually finish. The material decision is quick, the paper element is quick, and the result is a usable object rather than a sample.
Understand what the cover board actually does
In an accordion book, the pages are a continuous strip folded back and forth. That strip can stand, stretch out across a table or be turned page by page, so the covers have three jobs: they protect the first and last folds, they give the book enough weight to sit open without wandering, and they carry the decorative surface you see when the book is closed.
Book board, sometimes sold as binder's board or greyboard, is a dense, rigid board made from paper pulp. It is not the same as cardstock, mount board or corrugated card. Cardstock bends when you push the corner of a cover; book board resists. That stiffness is what stops a thin cover from curling around the folded block. The distinction matters because the boards are usually thicker than the paper block and are covered separately with decorative paper.
For an accordion book, the covers are usually two separate boards rather than one continuous piece. Each board is slightly larger than the folded page block on the top, bottom and fore-edge, while the spine side sits close to the first fold. Those overlaps are what create a visible border and protect the page edges.
Weight, thickness and stiffness are different things
Board is often described by grams per square metre, but gsm alone does not tell you how a board will behave. Two boards with the same nominal weight can differ in thickness, density and rigidity depending on how the pulp is formed and pressed. What matters for a cover is whether the board holds a flat plane under its own weight and whether it can be covered without bowing.
As a working guide, a board around 1.5 mm to 2 mm thick suits a small to medium accordion book, roughly the size of a postcard or a little larger. Thinner board, around 1 mm, keeps a tiny book light and is easy to cut by hand. Thicker board around 2.5 mm gives a larger book a solid, satisfying cover but needs a firm cutting technique and a decorative paper that can wrap the thickness cleanly. These are starting points, not rules; the finished size and the number of folds in the block change the balance.
A useful test is to hold a scrap of board by one edge and see how far it bends. If it flexes noticeably at the corner, it will show that flex in a finished cover. You can also cut two small squares and glue them back to back with your intended cover paper to see whether the combined layers stay flat or curl. This small sample costs minutes and answers the question better than a specification alone.
Matching the board to paper grain
Paper and board have a grain direction. When the mill forms the sheet, the fibres tend to align, and the board is stiffer and bends more easily across the grain than along it. In book work, grain matters because glue and covering paper can pull a board out of shape.
The practical rule for a cover is to run the grain of the board and the grain of the covering paper in the same direction as the spine or the fold of the book. On a small accordion book the effect is subtle, but a board whose grain runs the wrong way can bow after the cover paper dries. If you cannot identify the grain, bend a scrap gently in both directions; the direction that bends more easily is across the grain, and the grain runs along the other direction.
Choose boards that suit your first project
For a first accordion book, buy boards that are uniform, cleanly cut and easy to handle. A pack of cut book board or a larger sheet you can trim yourself both work. Pre-cut packs save the frustration of scoring and snapping thick board, while a sheet gives you complete control over cover size. A metal ruler, a sharp craft knife and a cutting mat are the tools that make board cutting clean; a dull blade tears the surface and produces ragged edges that show through a thin cover paper.
Think about the covering material at the same time. A decorative paper, book cloth or even a lightly textured wrapping paper can cover the board, but each has a different tolerance for folding around the edge. Thin, smooth paper wraps corners neatly with less bulk. Thicker paper and cloth need a slightly larger turn-in and a firm, even glue application so the corners stay flat. If you want the board to show as a plain, natural edge, a coloured or textured board can be left uncovered on the inside, but the cover still needs an attached surface on at least one side to keep the board from warping.
A few small purchases make the first attempt much more likely to succeed: a cutting mat, a sharp blade, a bone folder for creasing the covering paper, and a glue that suits paper. A PVA-type bookbinding glue is common because it dries clear and remains flexible; apply it thinly and evenly rather than flooding the board, because excess moisture is one of the main causes of a cover that dries with a bow.
Turn the interest into a balanced project
The simplest first accordion book uses a strip of paper roughly 10 cm tall and about 80 cm to 100 cm long, folded into panels of 10 cm to 12 cm. The number of panels is a design choice: every fold is a page turn, so a shorter strip with fewer folds is easier to manage, while a longer strip makes a book that unfolds impressively. The cover boards should be a few millimetres larger than the folded block on the top, bottom and fore-edges.
Sequence the work so nothing is cut before the measurements agree. First decide the finished panel size, then calculate the length of the folded strip and the number of folds. Cut the strip and fold it with a bone folder, pressing each fold flat. Next cut two cover boards to the finished size plus the overlap you have chosen. Cut the covering paper large enough to wrap around each board with a turn-in of roughly 1 cm to 1.5 cm on all sides. Glue the covering paper to the board, fold the turn-ins over, and press the cover under a weight while it dries. Attach the first and last panels of the folded block to the inside of the covers, then check the book opens and closes without pulling.
This is the point where the board choice earns its keep. A board that is too thin makes the finished book feel like a folded card; a board that is too thick makes the cover heavy and the turn-ins bulky. Handling two or three board samples before committing to the full project is the most reliable way to find the weight that feels right in your hands.
What to buy first and what can wait
Start with a modest supply of book board in a thickness you can cut confidently, a covering paper you like, and a paper for the folded block that is sturdy enough to fold without cracking. Add a bone folder, a cutting mat and a sharp blade. A dedicated corner cutter or a pre-cut board pack is a helpful upgrade once you know the size and weight you prefer, and coordinated covering papers let you make a set of books that look intentional rather than improvised.
The appeal of an accordion book as a first project is that it teaches the same core decisions that larger books demand: how board thickness influences structure, how grain affects flatness, and how covering paper and adhesive work together. A single finished book is a small, useful object and a clear record of those choices, ready to hold photographs, notes or a sequence of drawings.