Double-Sided Tape Placement for Accordion Books That Hold Their Shape

Double-Sided Tape Placement for Accordion Books That Hold Their Shape

An accordion book looks almost self-explanatory: fold a strip of paper back and forth, add covers, and the structure is done. The detail that decides whether it opens cleanly, stands without flopping, and survives handling is where the double-sided tape goes. Tape applied in the wrong band can lock a valley fold shut, pull a page into a curve, or leave the cover peeling at the spine edge. Preparing the supplies with that placement in mind turns a quick fold project into a satisfying, durable object.

Start with the paper decision, not the tape

Double-sided tape bonds on contact and does not slide, so the paper has to be right before any adhesive is exposed. Accordion pages work best in a paper that folds without cracking and holds a crease, commonly a medium-weight cardstock or a smooth text-weight paper backed with a slightly heavier cover stock. Weight in gsm indicates mass per area, not thickness or stiffness; a heavily sized 160 gsm sheet can feel stiffer than a softer 200 gsm one. Test a scrap by folding it both with and against the grain. With the grain, the fold line stays smooth; against it, the paper may craze along the crease.

Cut the page strip with the grain running along the length of the accordion so every fold crosses the grain. A strip roughly 10–15 cm tall and long enough for an odd number of panels gives a book that opens into a balanced shape. Odd panel counts let the book stand in a zigzag on a table with a panel facing forward at each end.

Which tape belongs where

Double-sided tape has three jobs in an accordion book, and they suit different tape types:

  • Cover attachment. A permanent, thin tape with a strong film carrier sits flat between the cover board and the first and last panels. Thin tape prevents a visible ridge.
  • Spine reinforcement. A narrow strip of tape or a paper hinge runs along the outside spine edge where the cover meets the first panel, taking the opening strain.
  • Temporary or repositionable work. Removable tape holds panels in alignment while you check fold counts, then comes away without tearing the surface.

Foam tape is the wrong choice anywhere in the book body: its thickness creates a gap at the fold and a visible step between panel and cover. Tape width matters too. A 6 mm tape suits narrow spine hinges; a 12–25 mm tape covers more area on a cover join and reduces the chance of a corner lifting.

Prepare the workspace so placement is accurate

Contact adhesive rewards preparation. Set out the following before peeling any backing:

  • A clean, dry cutting mat larger than the open book.
  • A steel ruler and a craft knife for trimming panels and cover boards square.
  • A bone folder or blunt scoring tool for creases.
  • A pencil and a light eraser for registration marks on the inside faces.
  • Double-sided tape in at least two widths, plus a small pair of scissors for cutting tape to length.
  • Scrap paper for testing tape adhesion on an offcut of the same paper.

Mark the fold lines on the back of the page strip, score each one against a straightedge, then fold and burnish. Pre-creasing is what lets the tape sit flat; trying to crease through tape already applied distorts the adhesive layer and can push the carrier film out of line.

Placement on the cover join

Lay the folded page block flat, open at the first panel. Run tape along the back of the first panel, inset a few millimetres from the head, tail and fore-edge. The inset stops the tape from squeezing out when the cover is pressed down. Place the cover board in position, align the edges, and press from the centre outward with a bone folder. Repeat at the last panel.

The critical placement is the hinge. A strip of tape along the outside of the first fold, running parallel to the spine edge, bridges cover and page and controls how the book opens. If the tape crosses the fold line itself, the fold cannot close fully and the book will not lie flat. Keep tape only on the flat faces either side of the crease.

Add a paper hinge for a stronger cover

A strip of thin paper the height of the book, about 2–3 cm wide, folded in half along its length, makes a hinge that covers the tape line and hides the join. Tape one half to the inside cover, one half to the first panel, with the fold of the hinge sitting exactly on the book's spine fold. This is the step where a thin tape and careful alignment matter most; a hinge applied off-centre shows as a crooked spine.

Test before committing

Before pressing the final cover down, close and open the book several times with the tape still lightly held. Check that:

  • The first and last panels meet the cover edges squarely.
  • Every fold closes with no tape crossing it.
  • The book stands in a zigzag without the covers splaying.
  • No adhesive is visible at head, tail or spine.

If alignment is wrong, removable tape and a light touch let you lift and reposition the cover before the permanent bond is pressed. Once pressed, double-sided tape is difficult to reverse without damaging the paper surface.

Finishing touches

Trim any tape overhang with scissors before it catches on the cover. Decorate the panels before assembly rather than after, using a bone folder to burnish collage and stamped areas flat. If you plan to add pockets or page inserts, place them on panels away from the spine hinge so the extra thickness does not interfere with the fold. A finished accordion book with well-placed tape opens crisply, stands as intended, and holds its covers through repeated use and display.

Back to blog

Useful Supplies for This Topic

Bring the useful supplies for this topic together and prepare a more organized, enjoyable next project.

Supplies, practical uses and Amazon links
SupplyWhat it helps withView
A5 paper trimmerTrim paper pieces that fit the cutter's working size.Amazon
Scrapbook adhesive tape runnersAttach suitable paper layers neatly in a card or scrapbook.Amazon
Small-parts organizer boxesSeparate beads, findings and other small craft components.Amazon

As an Amazon Associate I earn from qualifying purchases.

Explore Our Digital Guides

Follow a clear plan for organizing, making and finishing your next project with our practical digital guides.