Preparing Bookbinding Thread for Fold-Out Pages
Share
Fold-out pages turn a handmade book into an interactive object: a page that opens to reveal a wider spread, a hidden note, or a layered map. When bookbinding thread is the featured material, the fold-out page is where thread choice and fold preparation meet. Success is in preparation: select thread that suits the fold action, test the fold, and ready the signatures and covers before the binding thread is cut.
Why fold-out pages change your thread plan
A fold-out page moves every time the book opens. The thread at the spine and attachment points must hold that movement without abrading the paper. Fold-outs also add bulk, so the spine and cover need more room. Thread preparation begins with matching thread to the added movement and bulk, not just choosing a colour you like.
Match thread to fold action and paper weight
For fold-outs in sketchbooks or memory books, choose a strong, smooth thread with a firm twist. Waxed linen thread resists fraying and has a pleasant grip when pulled through signatures. Polyester or cotton-polyester binders' thread has low stretch and works well for books that will be opened repeatedly. Natural cotton thread is pleasant to handle but can abrade if the paper edge is rough.
Paper weight matters because a heavy card fold-out pulls harder on stitches. Use a thread thick enough to fill the hole punched in the paper. If the thread is much thinner than the hole, stitches sit loose and the fold-out wobbles. If the thread is much thicker than the hole, the paper distorts and the spine will not close flat.
Ready the fold before you pierce
A fold-out page is only as good as its score. Score cardstock or heavy paper along the fold line with a bone folder before creasing. This compresses the fibres and prevents cracking along the spine edge. Crease with the fold line parallel to the paper grain where possible; a fold across the grain fights the paper and can split the surface.
Once scored, fold the page gently back and forth once to establish the crease. Then open it flat before piercing. Piercing a closed fold risks trapping paper dust and misaligning holes. Place the fold-out page on a cutting mat or a scrap of book board, and pierce straight through along the spine edge.
Plan the fold-out structure and thread paths
A fold-out page is usually attached to a signature by one of two methods: as part of the signature itself, or as an extension that is tipped or sewn in separately. The simplest reliable method for a first book is to include the fold-out as a page within the signature, with its folded edge aligned to the spine. This uses the same sewing path as the rest of the book.
If the fold-out must open wider than the page block, make it slightly narrower than the other pages so the folded edge does not protrude beyond the text block. A common allowance is 2–3 mm shorter at the spine edge, but check against your own folded page once scored.
Prepare the signature and sewing stations
Before threading a needle, assemble and count the pages of each signature. Fold-outs add thickness, so keep each signature to three or four sheets rather than five or six. Press the folded signatures under a weight for a few minutes so the folds settle.
Mark sewing stations with a pencil on the closed spine edge. For fold-out pages, place stations slightly inside the spine edge rather than exactly at the fold. The thread should pass through the paper, not through the air gap at the fold. Use an awl to pierce each station through the whole signature, keeping the awl vertical.
Cut thread with handling allowance
Cut binding thread about three times the length of the spine plus enough to thread the needle. For a fold-out book with four or five stations, a length of roughly 90–120 cm is enough for a single signature and cover attachment. Wax the thread by drawing it through a block of beeswax or a candle stub, then run it between your fingers to warm it. Waxed thread grips the paper, reduces fraying, and helps knots hold.
Thread your needle with the waxed end and tie a small knot, or leave a tail to be worked in later. Keep the thread on the table rather than dangling, so it does not snag on the fold-out edge.
Prepare covers and the spine allowance for fold-outs
Fold-out pages add thickness at the spine. A cover cut flush with the text block on three sides may bow when the fold-out opens. Cut the cover boards about 3–5 mm taller and wider than the text block on the top and bottom, and give 6–8 mm at the spine edge, depending on the number of fold-outs. Check by wrapping a strip of cover material around the folded text block before cutting the final boards.
For a soft cover, use a paper or card that can flex without cracking at the spine. Score the spine line firmly so the cover hinges cleanly. For a hard cover, leave a small gap between the spine board and the cover boards to allow movement.
Work in stages: pierce, sew, and check the fold-out
Preparing for the next stage means testing the fold-out before you commit to the full binding. After you pierce and before you sew, place the fold-out page into the signature and press it flat. Open and close the fold-out once to check that its folded edge clears the sewing stations. If it catches, shift the stations inward by 1–2 mm and re-pierce.
Sew the signature with a running stitch or a simple pamphlet stitch, pulling each stitch snug but not tight enough to tear the paper. For a first fold-out book, a three-hole pamphlet stitch is quick and easy to adjust. When you reach the fold-out page, make sure the thread enters through the pierced hole and does not cross the fold line. Finish the sewing by tying off the thread inside the centre fold of the signature.
Check the thread tension and fold
After the first signature is sewn, open the book gently at the fold-out. If the thread pulls visibly against the paper, loosen the last stitch slightly. If the fold-out flops without support, tighten the stitch next to it. Then close the book and check that the fold-out lies flat. Press the closed book under a weight for a few minutes before attaching the cover.
These small checks help you prepare the cover and thread for the next stages without undoing already-sewn work.
Thread and tool choices that support the preparation
A few inexpensive items make fold-out preparation more reliable. A bone folder scores and creases folds crisply. A beeswax block or a waxed thread spool improves grip and reduces fraying. A bookbinder's awl pierces clean holes; a cutting mat protects the table. Choose a needle with an eye large enough for your thread but not so large that it enlarges the hole. For fold-out books, a blunt tapestry needle works well for pierce-and-sew methods because it parts the paper rather than cutting it.
Good thread is worth the time. A spool of waxed linen or polyester binding thread lasts for many projects, handles repeated opening, and keeps its twist. Keep the spool and a needle case together with your bone folder and awl so the next fold-out project is ready to start.