Plan Vertical Space in Freestanding Units for Remote Controls and Small Electronics
Share
Use the height you already have, not the footprint you wish you had
Remote controls and small electronics are awkward to store because they are short, flat, light and irregular. A sofa-side caddy, a shelf unit beside the television or a cubby in a freestanding cabinet usually offers more height than a pile of remotes can use. The useful planning move is to treat that vertical room as a stack of shallow, defined zones rather than one open void. You are not building anything; you are choosing movable dividers, trays and small containers that let you see and return each device without digging.
Start by measuring the internal space that actually exists
Work from the inside of the unit out. Measure the internal width, internal depth and internal height of the shelf, cubby or basket you intend to use. Note the thickness of hinges, the swing of doors, the travel of drawer runners and any handle that intrudes into the opening. A shelf that looks generous from the front can lose several centimetres at the back to a door closer or a raised lip. These measurements decide which containers will slide in easily and which will jam.
Then sort your electronics by retrieval rate rather than by size. The remote used several times an evening needs the most accessible spot at roughly hand height. Charging cables, spare batteries, a game controller used occasionally and a small speaker can sit higher or deeper. Grouping by frequency turns a single crowded shelf into a logical vertical column: immediate items low and forward, occasional items higher or toward the back.
Count devices honestly and note the shape of each one. Two remotes and a streaming stick box nest neatly; a games controller with protruding thumbsticks and a charging station needs more depth and headroom than its footprint suggests. Measure the tallest item in each group and the deepest, then keep those numbers as your real constraints. A container is useful only if the full device, including a protruding cable or stand, fits inside it.
Divide the height into usable zones
A simple approach is to plan in horizontal bands inside the unit. Give each band a job and a height just large enough for its contents. A low band holds the daily remotes in a shallow tray; a middle band holds a docking station or the controller in an open-front box; a top band holds a lidded container for batteries, spare leads and adapters. Keeping bands shallow means each item stays visible from above and can be lifted out without removing the band above.
This banded arrangement works with the products that suit it. Open-front corrugated or fabric cubbies let remotes be dropped in from the front. Shallow stackable trays use height by adding layers instead of scattering items sideways. A small three-tier desk organiser can sit inside a wide shelf and turn one dead level into three. Adjustable shelf inserts or riser shelves create a second floor inside a single cubby, though their supports must rest securely on the existing base and not rely on fixing into the unit.
Choose dividers that match the actual interior. Slotted dividers suit thin remotes and cable bundles; a set of small open boxes suits mixed accessories that would otherwise slide together. Lidded boxes are useful for items you want out of sight, but only where the lid can be opened without hitting a shelf above. A clear-front box helps you identify a controller or adapter at a glance, while an opaque fabric box hides visual clutter in a living area.
Match containers to the way electronics behave
Small electronics bring two practical conditions. First, cables tangle and catch on rough edges, so smooth interiors and rounded corners make a container easier to use. Second, devices are often charged where they are stored, which means you need space behind or beside the container for a cable to pass. Choose a tray with a cut-out, or leave a deliberate gap at the back of the shelf so the lead can run to a socket without pinching. Do not seal a charging device inside a tight lidded box; leave room for the cable and for the device to sit flat.
Weight is usually low, but a power strip or a small speaker changes the requirement. A light container can sit on an adjustable riser; a heavier item should rest directly on the shelf base. This distinction matters more than nominal volume. An organiser may list external dimensions that fit the opening while its internal compartments are too narrow for a controller. Read internal dimensions wherever they are given, and when they are not, judge by the largest item you intend to place inside.
- Shallow open trays: best for daily remotes, where speed of return matters more than concealment.
- Open-front boxes: suit controllers and charging cradles that need front access and a little headroom.
- Stackable trays or riser shelves: add a second usable level inside a tall cubby without altering the unit.
- Small lidded containers: keep batteries, adapters and spare leads together and out of sight where height allows.
- Slotted dividers: separate flat remotes and keep cables from knotting into one bundle.
Arrange for return, not just for storage
The vertical layout succeeds when returning a remote takes one motion. Put the daily tray at the front edge of its band, not behind a decorative object. Reserve the lower accessible zone for the items used most and keep occasional items above. If a child or a guest regularly picks up a remote, place that tray low enough to be reached comfortably. Label containers only where the contents are not obvious; a small label on a lidded accessories box helps, while a label on the daily tray adds fuss.
Leave a little slack. Containers that exactly fill a cubby are hard to pull out, and trays that pack tightly prevent a cable from lying flat. A finger-width gap at the front and a centimetre or two above the tallest device make the arrangement easier to live with. Check that drawers and doors still close with the new containers in place, and that a riser does not block the back of the shelf where cables run.
Finish the setup with a quick test
Load the unit and run through a typical evening. Pick up each daily remote, return it, plug a controller in to charge and open the lidded box for a spare battery. If any step requires shifting another container, the vertical zones are too tight or wrongly ordered. Adjust by moving a tray to a lower band or by replacing a deep box with a shallower one rather than by adding more containers.
The result is a freestanding unit that uses its height deliberately: daily electronics at hand, charging space respected and small accessories gathered where they can be found. The supplies that make this work are ordinary and movable, so the arrangement can change as devices come and go without any work to the room itself.