Fabric Bunting That Hangs Well: Choosing Material for Folded Edges and Hems
Share
Fabric bunting lives or dies by its edges. A triangle of quilting cotton pressed into a crisp double-fold hem hangs differently from the same shape cut in a loose-weave linen and simply sewn right sides together. The difference is not fussiness. It is the fold line, the hem bulk, and how the material behaves once gravity and a little outdoor air get involved. Choosing fabric with the hem treatment in mind makes the flags sit flat, turn points cleanly and look intentional from both sides.
Two edge methods, two different material demands
Most fabric bunting uses one of two constructions. The first is a folded-edge pennant, where the top edge, and sometimes the two sloping sides, are turned under and stitched, leaving a single layer of fabric and a visible hem line. The second is a layered pennant, where a front and back piece are sewn right sides together, turned through a gap and pressed, giving a clean reversible flag with a seam along the perimeter. The first method is faster and uses less fabric; the second hides raw edges and gives a more substantial drape, but it also needs a material that presses and turns without bulk at the point.
The material decision changes with the method. A folded-edge flag wants a fabric that holds a crease, stays put under the presser foot and does not fray faster than the hem can contain it. A layered flag wants a fabric that is stable enough to keep two pieces aligned, thin enough to turn through a narrow point, and opaque enough that a strong print does not show through the back.
What a fabric contributes to a hemmed flag
The angle that matters here is not colour or theme but how the cloth behaves at the fold. Three properties drive the result:
- Body and crease retention. Cotton poplin, quilting cotton and similar firmly woven medium-weight cloths take a pressed fold and keep it while stitching. Very soft lawns and rayons can ripple along a turned edge because the fabric shifts as the needle enters.
- Fray tendency. Tightly woven cotton frays slowly enough that a double-fold hem works well. Loosely woven linen, drapery-weight fabrics and coarse burlap shed threads quickly, so a folded hem needs a wider turn or an enclosed layered construction.
- Bulk at the tip. A layered pennant ends in a seam allowance tucked into a point. Mid-weight cotton turns cleanly if the corners are trimmed before turning. Heavy canvas or thick upholstery fabric gathers into a lump at the point and resists a sharp crease, so it suits a folded-edge flag with a plain squared or slightly clipped tip better than a long sharp triangle.
A useful test before committing: cut a small square of the candidate fabric, fold it double the way the finished hem will sit, press it, and stitch along the fold. Open it out and look for puckering, needle holes that do not close, or a fold that springs open. This is the cheapest way to learn what the cloth will do, and it takes a few minutes. It also tells you whether the fabric needs a slightly longer stitch or a lighter needle.
Matching hem width to fabric weight
For folded-edge pennants, a first turn of about 6 mm and a second turn of about 10 mm gives a tidy double-fold hem on medium-weight cotton with a 1 cm finished width. On lighter fabric, keep the same proportions but reduce the second turn slightly; on heavier fabric, widen the first turn so the raw edge is fully captured. Record the fold widths you settle on and apply them to every flag so the set looks consistent when hung together.
If you are cutting triangles rather than rectangles, remember that cut dimensions and finished dimensions differ. A flag cut 20 cm wide at the top and 25 cm deep will finish smaller once all edges are turned. Decide the finished pennant size first, then add the hem allowances to the cut piece. For a double-fold hem on the two sloping sides and the top, that can add several centimetres to each side, so plan the spacing along the tape accordingly.
Pinking shears are sometimes suggested as a shortcut for the sloping sides of a single-layer flag. They slow fraying but do not stop it entirely, and they leave a serrated edge that reads as a deliberate finish only if it is consistent. A stitched double-fold hem is the more durable choice for bunting that will be handled, stored and rehung.
Linings, interlining and the see-through problem
Layered bunting is often made from two contrasting prints, which is part of its appeal. Some pale or thin fabrics become translucent against a window or in bright daylight, and a bold print on the reverse will show through. If you want the flags to read cleanly from both sides, choose a closely woven fabric with enough opacity, or add a lightweight woven fusible interfacing to one layer before sewing. Interfacing also gives soft cotton a little more body, which helps a turned point hold its shape. Skip heavy interfacing: it stiffens the flag and makes the turning step harder.
Fusible interfacing needs a pressing cloth and a temperature that suits the fabric, and the adhesive side must face the wrong side of the cloth. Follow the manufacturer's instructions rather than guessing, since the bonding requirements vary between products.
Construction sequence for a layered flag that turns cleanly
The following sequence applies to a reversible pennant with a straight top edge and two sloping sides, before it is attached to the tape:
- Cut front and back pieces to the same size, adding a seam allowance of about 1 cm on the sloping sides and top. Treat the top edge separately if it will be enclosed in the tape.
- Place the pieces right sides together. Stitch the two sloping sides with a short stitch length at the point, then stitch the top if it will not be hidden.
- Trim the seam allowance across the point to reduce bulk, and clip the corners where the sloping sides meet the top.
- Turn the flag right sides out through the open top, easing the point out with a blunt tool such as a chopstick or point turner. Press the sloping seams flat, then press the flag.
- Topstitch close to the edge if the fabric is stable enough; this is optional but flattens the seam and strengthens the edge on frequently handled bunting.
If the top edge will be sewn into a binding tape or a folded strip of fabric, leave it open and let the tape close it. That join hides the raw edge and avoids a doubled seam at the top of each flag.
Attaching the flags without ruining the edges
A fabric tape, bias binding or a folded strip of the same fabric can carry the flags. Space them evenly, and decide whether they will be permanently stitched or slipped into loops for removable use. Permanent attachment is quicker and gives a strong result; removable loops suit bunting that will be washed or restyled. Either way, the tape should be wide enough to hold the flag top securely and should be stitched along both long edges so it does not twist.
For bunting that will hang outdoors, choose a fabric and thread that suit the expected conditions. Natural cotton fades and weakens with prolonged sun and damp, so a polyester or poly-cotton blend is the more durable choice for outdoor use. Indoors, the visible hem, the drape and the print matter more than weather resistance.
Tools that make the hemming decision easier
An iron with a clean soleplate and a pressing cloth, a hem gauge or simple card template for turning consistent folds, and a pair of sharp fabric shears do more for tidy bunting than any single fabric choice. A walking foot can help if you are sewing several layers or a slightly slippery fabric, and a fine pin or a small clip keeps a turned point in place while you stitch. These are ordinary sewing-room tools; the point is to use them on a test piece first so the fabric, fold width and stitch length are settled before you cut a full set of flags.
Bunting is a small project, which makes it a good place to learn how a particular cloth behaves at a fold. Once you know whether your chosen fabric presses, turns and frays cleanly, the same knowledge carries over to pouches, bags and other sewn pieces where the edge treatment is the difference between homemade and well made.