How to Make Scrunchies With a Facing That Holds Its Shape

How to Make Scrunchies With a Facing That Holds Its Shape

A scrunchie looks like a small, forgiving project, and in most respects it is. The part that separates a scrunchie that flops open and twists out of shape from one that holds a clean, rounded profile is the way the elastic channel is closed. Many tutorials simply fold the tube and stitch, which works, but leaves a raw or narrow seam edge sitting right where the elastic pulls hardest. A facing is a cleaner solution: a separate strip of fabric that finishes the opening, gives the elastic channel a stable edge and lets you turn the tube neatly. Understanding what a facing does in this context helps you choose fabric and build a scrunchie that survives repeated stretching.

What a facing actually does on a scrunchie

A facing is a piece of fabric sewn to an edge and turned to the inside, so it finishes that edge and adds a little structure. On a scrunchie, the edge in question is the short opening left in the tube where the elastic goes in. Without a facing, that opening is usually just a gap in the seam, and the fabric around it takes all the strain when you stretch the elastic to tie it off.

A facing strip gives you three practical benefits. It reinforces the opening so it does not distort when the elastic is pulled through and knotted. It lets you enclose the seam allowances neatly instead of leaving them loose inside the tube. And it gives you a deliberate place to anchor the elastic ends, which keeps the finished scrunchie from twisting into a spiral after a few wears.

Facing versus a plain fold-over finish

The simple fold-over method is faster and perfectly adequate for a lightweight, decorative scrunchie. A facing earns its extra steps when you use a fabric that frays easily, when the scrunchie is a gift and you want a tidy interior, or when you are working with a heavier fabric such as linen or a firm cotton that would make a folded edge bulky. If you are making several scrunchies as a set, a facing also gives a more consistent result, because you are not relying on the tube turning evenly.

Choosing fabric for the outer and the facing

The facing does not need to match the outer fabric, and choosing it deliberately is part of the project. A lightweight woven cotton or a cotton-polyester blend makes a good facing because it presses flat, holds a crease and does not add bulk. A scrap of the same fabric works well if the outer is already light. Avoid using a piece of bulky or highly fraying fabric as the facing, since it will fight the narrow turn and make the opening lumpy.

The outer fabric should have enough body to gather attractively around the elastic. Crisp cotton, cotton lawn, lightweight linen and soft blends all work. Very slippery satins and chiffons can be used, but they require more careful pinning and a facing that will not slide out of alignment. If you are matching a print, check the direction of the motif before cutting, and remember that a scrunchie is a tube, so the print will wrap around.

Making a scrunchie with a faced opening

The following method describes one scrunchie. Finished size and cut size are different, so take a moment to establish your own dimensions rather than assuming a universal measurement. A common finished scrunchie has an outer circumference of about 18–20 cm (7–8 in) when relaxed, with a fabric strip roughly 45–50 cm long and 9–10 cm wide before seaming. These are starting points, not fixed specifications; a larger, fuller scrunchie needs a longer and wider strip.

Cut and prepare

  • Cut one outer strip and one facing strip. The facing should be about 5–6 cm long and the same width as the outer strip.
  • Press both pieces. If the outer fabric is directional or has a nap, mark the top edge before you lose track.
  • Fold the outer strip in half lengthwise with right sides together and pin along the long edge.

Sew the main tube

Stitch along the long edge with a seam allowance of about 1 cm (3/8 in), leaving a gap of roughly 5–6 cm near the middle of one end for turning. Backstitch at both ends of the seam. This gap is where the facing will be attached, so keep it clear and even. Do not trim the seam allowance yet; a slightly wider allowance helps the facing sit without pulling.

Attach the facing

Fold the facing strip in half widthwise with right sides together and stitch the short ends, forming a small loop. Press the seam open. Turn the facing right side out and press it flat so the seam sits along one edge. Now pin the facing to the right side of the tube opening, matching the facing seam to the gap edges. The facing should extend into the opening by about 2–3 cm so it overlaps the seam allowance. Stitch the facing to the tube around the opening, using a seam allowance slightly narrower than the main seam so the facing edge stays inside the finished tube.

Turn, fill and close

Turn the tube right side out through the facing opening. The facing will roll to the inside, giving a clean edge. Press the tube so the seam sits along one side. Cut a length of elastic — about 20–25 cm for a standard scrunchie, adjusted to the wearer's hair volume and your own preference for tension. Thread the elastic through the tube using a safety pin, bring both ends out through the facing opening and overlap them by about 2 cm. Stitch the ends together securely with a zigzag or several passes of straight stitch. Slip the joined elastic back inside, then close the facing opening by hand with a small ladder stitch or by machine close to the edge. Hand stitching gives a cleaner finish here because you can hide the thread inside the facing layer.

Avoiding bulk and twisting

The most common problem with a faced scrunchie is bulk at the opening. It comes from three places: a seam allowance that is too wide, a facing that is too heavy, and too much overlap between facing and tube. Keep the facing light, grade the seam allowances where they meet and avoid pressing the opening flat after turning, because a hard crease there makes the scrunchie sit awkwardly in the hair.

Twisting usually comes from the elastic join not being aligned with the seam. When you stitch the elastic ends together, check that the join sits against the side seam, not across the open face of the tube. If the join is offset, the scrunchie will rotate as it is worn. A quick alignment check before you close the opening saves unpicking later.

When a facing is worth the extra step

A facing is a small construction choice, but it changes the result. It is worth adding when you are making scrunchies from fabrics that fray, when you want a neat interior for gifting, or when you are producing a coordinated set and want a repeatable finish. For a quick everyday scrunchie in a stable cotton, the simpler fold-over method remains a good option. Choosing the method to match the fabric and the purpose is the same decision that applies to most sewing: match the construction to the material and the job the finished object needs to do.

Back to blog

Useful Supplies for This Topic

Bring fabric, measuring and stitching tools together for your next sewing project.

Supplies, practical uses and Amazon links
SupplyWhat it helps withView
Cotton quilting fabric bundlePrepare cotton fabric pieces for patchwork and small sewn projects.Amazon
Fabric cutting shearsCut fabric with a dedicated pair of tailoring scissors.Amazon
Rotary cutter, mat and ruler setMeasure and cut straight fabric pieces on a suitable cutting surface.Amazon
Hand-sewing kitGather basic needles, thread and small hand-sewing tools.Amazon
Tailor's chalkMark cutting and stitching positions on suitable fabric.Amazon
Steam ironPress seams and folded edges during a sewing project.Amazon

As an Amazon Associate I earn from qualifying purchases.

Explore Our Digital Guides

Follow a clear plan for organizing, making and finishing your next project with our practical digital guides.