Joining Macrame Wall Hangings: The Feature That Decides Your Method
Share
Macrame wall hangings often grow from small components: several independent knots or motifs, a row of repeated diamonds, a fringe of tassels, two or three panels meant to sit together. Joining those pieces is where a wall hanging succeeds or fails visually, and the method depends on one thing more than any other. Before you choose between tying, sewing, knotting onto a shared cord or building a new connecting element, identify the feature that changes the answer: whether you need to see the join, and how much the piece will move once it hangs.
Two wall hangings can look identical at arm's length and need completely different joins because one is a static, stiff panel and the other has loose, swinging tails. That difference in expected movement, and in whether the join should read as a deliberate detail or disappear, sets your material, your tool and your technique.
Read the piece before choosing a join
Lay the parts on a flat surface in the order they will hang. Look at how the cords behave at the point of contact.
- Cut ends: a tassel, a fringe or the end of a panel presents loose cords you can knot, comb or sew.
- Loops and spaces: open diamond motifs and chain-style links give you an existing hole to thread with.
- Solid areas: dense rows of square knots leave little daylight between cords, so a join must either sit in front of them or be hidden behind.
- Focal points: a central motif or a distinct colour band is a visual anchor. A join placed near it will compete; a join placed along a quiet edge will recede.
That survey tells you whether you are connecting edges, ends or surfaces. Each needs a different approach, and the expected movement of the finished hanging tells you how robust the join has to be.
The feature that changes the answer: static panel or moving tails
A wall hanging that hangs flat against the wall and stays put tolerates a join that simply holds position: a sewn seam, a lark's head knot onto a shared bar, or a few well-placed diagonal cords will do the job. The pieces are not being tugged, twisted or swung.
A hanging with long loose fringes, dangling cords or separate strands that will swing when a door moves or a chair scrapes the wall puts repeated movement into your join. Here the method must keep the parts aligned over time, not just hold them together at the moment of assembly. Several practical consequences follow:
- Bring movement into the design: plan for the pieces to hang from a common top cord or ring so the weight is carried above the join, not through it.
- Keep joins away from swinging ends: a soft, low-profile join near the top survives better than a bulky knot halfway down a moving fringe.
- Match cord to the task: a smooth, firm cord holds a tidy knot through repeated movement more predictably than a slippery, loosely twisted cord, which tends to work its way loose.
- Hide the join behind the work: with moving tails, visible tidy structure is often better than a bulky front-facing knot that catches attention.
Joining by tying: the visible option
Tying is the natural choice when the join should be part of the design. A lark's head knot is the workhorse: fold a cord, pass the loop under a mounting bar or through an existing loop, and pull the ends through. It fixes a component to a shared support and reads cleanly on the front. A gathering knot wraps a small bundle of cords into a neat cylindrical join, useful at the start or end of a section. A simple overhand knot is the fallback when you only need to stop loose ends from separating.
Tying is fast, needs little more than your hands and a pair of sharp scissors, and is easy to undo if the spacing feels wrong. Its limit is bulk and movement: knots worked into a hanging area that will swing can loosen, and hard or slippery cords may need a second securing step.
Joining by sewing: the disciplined option
Sewing is the answer when a join should be invisible, low-profile and firmly fixed. It suits a static panel: matching or edge-to-edge components held in a flat plane. Use a sturdy needle and a thread or finer cord in a colour close to your working cord, and work small, closely spaced stitches through the cord structures rather than through the air beside them. A blunt or large-eye needle is easier to thread and easier to handle against a woven knot surface.
Sewing gives control and leaves the front face clean, but it is slower and more permanent. It is a poor first choice for parts that need to be repositioned while you check the balance of the finished hanging, and stitches placed where a swinging section flexes repeatedly will pull over time.
Joining with a shared structure
The third approach builds a new element that joins the parts by carrying them. A horizontal cord, dowel or ring at the top lets several panels or motifs hang from one line. This is the most forgiving method for a design with movement, because the structure above the join takes the load and the components simply hang.
- Dowels and rings give a crisp, straight or circular top edge and make the spacing of components easy to judge before committing.
- A horizontal cord works for a soft, organic line; check that components sit evenly along it.
- Additional short cords can bridge the gap between components, repeating the motif or plain cord and reading as an intentional design element rather than a repair.
Choose the shared structure whenever the components need consistent spacing, regular rhythm or a clean top edge. It is also the option that best keeps a large hanging stable, because you decide the layout before the piece is committed to the wall.
Choosing cord and tools for the join
Your joining material should match the working cord in fibre and thickness so the join looks consistent and responds the same way to any later finishing. A natural cotton macrame cord takes a firm, tidy knot and holds it; textile cords in the same family are easy to comb for fringes and tassels. Smooth, tightly constructed cords are predictable for structural joins; more textured cords hide joins better but can look crowded when gathered. Keep a few metres of matching cord aside for the join itself rather than recycling short offcuts, which are usually too short to work the gathering knots cleanly.
Useful equipment is modest but specific. Sharp scissors with fine points cut cord cleanly at the join without crushing it. A large-eye or tapestry needle in a size that clears the cord allows you to sew joins and to weave short tails back into the work. A measuring tape helps confirm even spacing, and a rigid measuring or spacing gauge, often called a macrame gauge, keeps repeated joints the same length. Strong clips or pins hold components in place on a work board while you check alignment; a felt or foam work board grips the cords. These tools improve the join by making it straight, even and repeatable.
Finishing a join
Once the pieces are attached, work the join and hide the evidence. Weave short loose tails back into the surrounding cord structure rather than cutting them flush; trimming cord ends on a hanging that will move tends to release them over time. If a join is sewn, check that stitches sit flat and the join does not pull or pucker. If the join is knotted and will show, even the spacing so the repetition reads as design rather than accidents. If the pieces hang from a top structure, check that each component sits at the intended height and that none of the joins carry the weight of the hanging. Blocking the finished wall hanging on a flat surface, if you use that finishing step, helps settle the cords so the join sits evenly.
A good join on a macrame wall hanging is one you notice only when you choose to look, or one the design invites you to see. Identify whether the piece is static and settled or moving and swinging, and decide whether the join should disappear or show. Those two answers tell you whether to sew, tie or build a shared structure, and they tell you which tools and cord support it.