Storing Woven Wall Hangings Between Display Periods
Share
Plan for the Months the Hanging Comes Down
A woven wall hanging spends part of its life on a wall and part of it in a cupboard, under a bed or in a lidded box. The way you choose a piece, its hanging hardware and its storage container determines how easily it moves between those two states and how consistently it comes back out looking the way it went in. The practical goal is a hanging that can be taken down without unpicking its finish, folded or rolled into a known container, and put back up without re-dressing the fringe or re-stretching the warp.
Selection for convenience and consistent storage is therefore not about buying the smallest or the cheapest hanging. It is about matching three things: the hanging's construction and size, the way it mounts, and the container you can actually keep in your home. Decide those together before you weave or buy, and storage stops being an afterthought.
Choose Construction That Survives Being Put Away
Wall hangings are built in several ways, and the construction affects what happens when the piece is folded or rolled. A flat tapestry on a shedding device or rigid heddle loom is usually a dense, stable cloth with warp ends finished at the top and bottom. Those ends, and any dowel or rod the piece hangs from, are the parts most likely to bend, kink or tangle in storage.
Warp finishes and dowels
Look for a top finish that releases cleanly. Warp ends tied in small groups and knotted close to the cloth travel better than long, loose fringe, which snags and creases when folded. A removable dowel is convenient because the cloth can be rolled or folded flat while the rod is stored separately. If the dowel is woven in or permanently attached, choose a hanging whose top edge will accept a soft fold or whose rod is short enough to fit the planned container; a rigid rod sets the minimum length of any storage you use.
Fringe and raised texture
Long fringe, looped pile, Rya knots and chunky roving create height. Two such faces pressed against each other can crush or interlock. Store these pieces with the pile facing outward, or roll them rather than fold them. A flatter weft-faced tapestry tolerates folding along warp lines, which can be practical when shelf space is limited.
If you are deciding between two pieces of similar size, the flatter construction will usually fold to a smaller footprint, while the heavily textured piece needs more protective space or a roll. Neither is better; the choice depends on where the hanging will live when it is not displayed.
Treat the Mounting Method as Part of the Choice
The mounting method decides how much dismantling is needed before storage. A hanging on a dowel with a cord loop lifts off a hook or nail in one movement. A piece stapled or tacked to a wooden strip usually stays attached to that strip, so the strip travels with it and adds length and bulk. A hanging suspended from a driftwood branch or a decorative rod has the same issue: the support is part of the object in storage.
For long-term convenience, favour a hanging you can lift off its support in one go and store with the support removed or kept in a dedicated slot. If you prefer a permanent decorative rod, plan a storage container long enough for the rod and a way to keep the cloth from sliding off it. A simple cloth sleeve or a pair of soft ties around the rolled hanging keeps the fringe together and stops the piece from unrolling inside a box.
Size the Container to the Hanging, Not the Other Way Round
Measure the hanging before choosing any container: finished width, finished length including fringe, and the diameter it reaches when rolled. A roll's diameter depends on the thickness of the weave, so measure a sample roll of the actual piece or, if you are planning ahead, use the planned yarn and sett to estimate whether it will roll thinly or bulkily. Record the measurements on a card kept with the container, so the piece can be matched back to its storage quickly.
The container should allow the hanging to lie flat or roll without being compressed at its edges. Because a woven piece is usually wider than it is deep, a shallow under-bed box or a wide flat drawer suits a folded hanging, while a sturdy tube or a long shallow box suits a rolled one. Avoid pressing the piece against a hard corner; a layer of acid-free tissue or a washed cotton cloth inside the container cushions edges and separates stacked pieces.
Containers that work in a household
- Shallow lidded storage boxes: good for flat tapestries kept in a drawer or under a bed; choose one with a close-fitting lid and enough length for the dowel.
- Sturdy cardboard or plastic tubes: good for textured or heavily fringed pieces; roll around the warp direction with the pile facing outward.
- Fabric dust bags: useful for a hanging that stays on a rod, and easier to hang or fold onto a shelf than a rigid box.
- Wide drawers with dividers: keep two or three small hangings apart so their fringes do not tangle and their edges do not take a set.
The right container is the one you will actually use in the space you have. A beautifully made tube that is too tall for the cupboard will end up propped in a corner and forgotten, so measure the shelf or drawer as well as the hanging.
Make the Take-Down and Rehang Routine Consistent
Convenience comes from repetition. A consistent sequence protects the piece and makes rehanging quick. Before taking the hanging down, note which side faced the wall and photograph or sketch the position of the rod, fringe and any decorative elements. Then remove the support, brush loose dust from the front with a soft brush, and fold or roll along the established lines. Place the hanging in its container with the recorded measurements and a note of any repairs needed.
Storing fringe consistently means keeping the groups of yarn ends aligned. A strip of tissue across the fringe, held with gentle ties, stops the ends from mingling with the next piece. When the hanging goes back up, the tissue comes away and the fringe falls into its original grouping, which reduces the need to comb or trim.
Why material composition matters here
Wool, cotton, linen, alpaca and synthetic yarns behave differently in storage. Wool resists creasing but is vulnerable to pests, so a clean, closed container and periodic inspection are practical habits. Cotton and linen fibres are strong but show fold lines sharply, so folding along the same lines repeatedly can weaken or mark them. Very soft, lofty yarns crush under weight, while tightly spun tapestry wool holds shape. These are general tendencies rather than guarantees; the specific yarn and sett of your piece decide how much protection it needs. If you know the fibre, choose padding and folding accordingly. If you do not, treat the piece gently and watch for creasing after each storage period.
Selecting a Hanging You Can Live With
When buying or commissioning a woven hanging, ask how it hangs and how it should be stored. A maker or seller can usually tell you whether the dowel is removable, what the finished dimensions are and how the fringe is secured. Use those answers to choose a piece that suits the wall, the container and the routine. A hanging with a removable rod, tidy warp ends and a moderate depth of texture will be easier to put away and bring out, while a textural statement piece is worth the extra care if it is the one that finishes the room.
The consistent result comes from treating display and storage as two parts of the same project. The yarn, construction and mounting that make a hanging satisfying on the wall can also make it easy to put away, provided the storage is chosen to fit the object rather than improvised after the fact.